59 lines
2.6 KiB
Markdown
59 lines
2.6 KiB
Markdown
# X10 Decoder
|
|
## Introduction
|
|
This is a protocol decoder for the Flipper Zero to decode the X10 series of devices when doing a read from the Sub-GHz menu.
|
|
|
|
|
|
|
|
|
|
## Validation
|
|
NOTE: As an Amazon affiliate I (CodeAllNight) earn from qualifying purchases from the amzn.to links below.
|
|
|
|
The code was tested with the "X10 Camera Control System Remote Control Model CR12A" which you can purchase from
|
|
https://amzn.to/3issZPs and should also be compatible with signals from https://amzn.to/3QEF7cM
|
|
|
|
The receiver I used is no longer for sale, but a similar module can be purchased from https://amzn.to/3CFWy6M
|
|
|
|
The House (Channel) is A-P setting.
|
|
The Unit (Button) is 1-16 setting (slider switches between 1-8 and 9-16).
|
|
The signal is "On" or "Off". For each channel there is also a "Dim" or "Bright".
|
|
|
|
The signal is broadcast at 310MHz with a modulation of AM650.
|
|
|
|
|
|
## Installation Directions
|
|
This project is intended to be overlayed on top of an existing firmware repo.
|
|
- Clone, Build & Deploy an existing flipper zero firmware repo. See this [tutorial](/firmware/updating/README.md) for updating firmware.
|
|
- Add the [x10.c](./x10.c) file to the \lib\subghz\protocols folder
|
|
- Add the [x10.h](./x10.h) file to the \lib\subghz\protocols folder
|
|
- Update the \lib\subghz\protocols\protocol_items.h file
|
|
- After all of the other #include statements add the following line:
|
|
```
|
|
#include "x10.h"
|
|
```
|
|
- Update the \lib\subghz\protocols\protocol_items.c file
|
|
- After all of the other &subghz_protocol_{name}, entries add the following:
|
|
```
|
|
&subghz_protocol_x10,
|
|
```
|
|
- NOTE: Your updated files should look similar to the [protocol_items.c](./protocol_items.c) and [protocol_items.h](./protocol_items.h) in this project.
|
|
- Build & deploy the firmware. See this [tutorial](/firmware/updating/README.md) for updating firmware.
|
|
|
|
|
|
## Running the updated firmware
|
|
These directions assume you are starting at the flipper desktop. If not, please press the back button until you are at the desktop.
|
|
|
|
- Press the OK button on the flipper to pull up the main menu.
|
|
- Choose "Sub-GHz" from the menu.
|
|
- Choose "Read" from the sub-menu.
|
|
- Choose the "Config" option (Click the left arrow)
|
|
- Change the frequency to 310.00 (Click the left arrow multiple times)
|
|
- Confirm that Hopping is OFF.
|
|
- Confirm the Modulation is AM650.
|
|
- Press the BACK button.
|
|
- The flipper should say "Scanning... and show 310.00 AM 00/50"
|
|
|
|
Click a button on your X10 remote.
|
|
|
|
The flipper should show "X10 <some code>"
|
|
- Press the OK button on the flipper
|
|
It should show the Channel, Button number and the kind of button (ON/OFF/DIM/BRIGHT). |